Seca 777 Digital Column Scale

by Seca - Authorized Reseller

Fast Delivery
Easy Returns

MPN:

550 lbs Capacity, 4-90 Inch Measuring Range - Each - #7771821009

$399.00

Qty

Skip to the end of the images gallery

Skip to the beginning of the images gallery

Description

Q/A

Description

The Seca 777 is a divine contender in a world of scales. Built to last from robust metal, the Seca 777 is designed for high-volume patient use in a healthcare setting. It has a built-in measuring rod that can accurately measure anything from 4 to 90 inches, and a digital readout for guess-free results. This scale includes rubber-coated casters for easy transportation without the worry that you'll leave marks on the floor. It also contains USB (Universal Serial Bus) connections for interfacing with a PC or EMR integration. Plus, the metal platform tilt-proof, so you never have to worry about stability when weighing patients. Don't forget to acquire other diagnostic equipment like Drive's Deluxe Automatic Blood Pressure Monitor.

How to Clean

Special care should be taken when maintaining a sanitized environment in the office. This product is no exception. Care should be taken to properly clean and maintain this device's cleanliness.

Clean this device with a soft cloth and soap suds for standard cleaning.
For disinfecting, use an alcohol-based disinfectant.
Using a soft cloth, wipe down the weighing platform and height measurement flap with disinfectant before and after each use.
Disinfect everything else when required.
This device cannot be sterilized.

How to Transport

Do not transport over long distances.
If needed, remove from power source.
Fold down measuring flap and fully lower measuring rod.
Use handle on device to pull.
Tilt device on corner where base meets rod.
Move device slowly over sils.
Return to upright position and plug into power source when done.

Made of Metal

A question: How many things today are made from plastic? Plastic is great -- it's durable, cheap, and easy to work with. However, everything made from plastic will eventually break sooner than things made from other materials. Many companies have adapted plastic for use in scales. This allows for cheaper scales to be available for everyone. However, it also means that these scales will not last nearly as long. For most people, this isn't a problem, but for demanding fields like the healthcare industry, broken scales are unacceptable. Recording weight accurately is an important part of patient analysis and diagnosis and every patient is different. A scale will need to be used by healthy weight and bariatric patients. This changing demand presents a problem that plastic is not equipped to answer. That's where the Seca 777 Medical Scale, which is made of metal, differs from other scales.

Troubleshooting

Problem	Cause	Remedy
No weight is displayed with a load on the scale	The device has no power supply	Check if the device is on If in battery mode, insert batteries If in power supply mode, ensure the device is plugged in
0.0 does not appear before weighing	A load was already on the device before it was switched on	Take the load off the measuring station Turn off measuring station then turn back on
----- appears before weighing	A load was already on the device before it was switched on	Take the Load off of the measuring station Turn measuring station off then on again
The weight display flashes.	Consistent weight value has not yet been detected	One of the following functions is active: Hold, Autohold, Tare. Wait until the measuring station has detected a consistent weight value Take the load off the measuring station, wait until 0.0 is displayed and weigh again
One display segment is displayed continuously or not at all	The display is defective	Inform Seca service
Low battery sign is displayed	Battery voltage is dropping	Change the batteries
bAtt is displayed	Batteries are dead	Change the batteries
StOP is displayed	Max Capacity Exceeded	Take the Load off the measuring station
Er:[No.]:11 is displayed	The device is too high or the load is too high in one corner	Remove the load from the measuring station and distribute weight evenly Turn device off then on again If the problem continues, inform Seca Services
Er:[No.]:12 is displayed	The device has been switched on with too high a load	Take the load off the measuring station Turn scale off then on again
Er:[No.]:16 is displayed	The device was caused to oscillate; the zero point could not be determined	Turn device off then on again
Er:[No.]:32 is displayed	An internal communication error has occurred	Turn scale off then on again If the problem continues contact Seca service